Sewing Machine Threading Diagrams

Step-by-step threading guides for the most popular sewing machine brands.

How to Thread Your Sewing Machine

Correct threading is the foundation of good stitching. Even a small mis-thread can cause tension problems, skipped stitches, or broken thread. Use the brand guides below as a general reference — always consult your specific model's manual for the exact threading path.

Singer

  1. 1Raise the presser foot and set the needle to its highest position.
  2. 2Place the thread spool on the spool pin and guide the thread through the upper thread guide at the top of the machine.
  3. 3Bring the thread down the right channel of the tension assembly, around the bottom, and back up the left channel.
  4. 4Hook the thread through the take-up lever from right to left.
  5. 5Continue down through the lower thread guides toward the needle.
  6. 6Thread the needle from front to back (or left to right on some models — check your manual).
  7. 7Insert the bobbin so thread unwinds counter-clockwise. Pull thread through the bobbin slot and under the tension spring, leaving a 15 cm tail.

Tip: Singer machines made after 1960 generally follow this path. Older treadle and vibrating-shuttle models differ significantly — refer to your manual.

Brother

  1. 1Raise the presser foot lever and bring the needle to its highest position using the handwheel.
  2. 2Place the spool on the spool pin (horizontal or vertical depending on model) and secure with the spool cap.
  3. 3Follow the numbered thread guides printed on the machine — most Brother models have guides labelled 1 through 6 or 7.
  4. 4Pass the thread through the tension disc assembly, then up and through the take-up lever.
  5. 5Continue down through the remaining guides to the needle bar guide.
  6. 6Thread the needle from front to back.
  7. 7Insert the bobbin into the front-loading or top-loading case per your model, and pull thread through the guide slot.

Tip: Brother machines have numbered threading guides printed directly on the machine body — follow them in order for a quick, accurate thread-up.

Kenmore

  1. 1Raise the presser foot and turn the handwheel to bring the needle to its highest point.
  2. 2Place the thread on the spool pin and guide it through the thread guide at the top of the machine.
  3. 3Bring the thread down and around the tension discs, following the channel on the front of the machine.
  4. 4Thread up through the take-up lever from right to left.
  5. 5Guide the thread down through the needle bar thread guide.
  6. 6Thread the needle from front to back and pull through about 10 cm of thread.
  7. 7Insert the bobbin into the bobbin case with thread feeding in the correct direction per your model's diagram.

Tip: Kenmore machines were manufactured by several different makers (Janome, Singer, White) over the years. Threading paths can vary — your model number will tell you the actual manufacturer.

Janome / New Home

  1. 1Raise the presser foot and set the needle to its highest position.
  2. 2Place the spool on the spool pin and guide the thread through the upper thread guide.
  3. 3Bring the thread down the front of the machine, through the tension assembly.
  4. 4Thread up through the take-up lever.
  5. 5Continue down through the needle bar guide.
  6. 6Thread the needle from front to back.
  7. 7For top-loading bobbins: drop the bobbin in, pull thread through the slot in the needle plate, and tug gently to engage the tension spring.

Tip: Most modern Janome machines use a top-drop bobbin system. The bobbin thread does not need to be pulled up manually — simply lower the needle once and the bobbin thread will catch.

Husqvarna Viking

  1. 1Raise the presser foot and bring the needle to its highest position.
  2. 2Place the thread spool on the spool pin and guide through the thread guide at the top.
  3. 3Follow the threading diagram on the machine or in your manual — Viking machines often have a thread path diagram printed on the front cover.
  4. 4Pass the thread through the tension assembly and up through the take-up lever.
  5. 5Continue down through the lower guides to the needle.
  6. 6Thread the needle from left to right (most Viking models).
  7. 7Insert the bobbin into the horizontal drop-in bobbin case and follow the arrow guide to seat the thread correctly.

Tip: Husqvarna Viking machines often thread the needle from left to right rather than front to back — check your model's manual to confirm the correct direction.

Pfaff

  1. 1Raise the presser foot and set the needle to its highest position using the handwheel.
  2. 2Place the spool on the spool pin and thread through the upper guide.
  3. 3Bring the thread down through the tension assembly, following the path marked on the machine.
  4. 4Thread through the take-up lever from right to left.
  5. 5Continue down to the needle bar guide.
  6. 6Thread the needle from front to back.
  7. 7Insert the IDT (Integrated Dual Feed) bobbin per your model's instructions, ensuring the thread feeds in the correct direction.

Tip: Many Pfaff machines feature IDT (Integrated Dual Feed) — a built-in walking foot. Ensure the IDT is engaged or disengaged correctly for your project type.

Need Your Model's Exact Threading Path?

General guides are a helpful starting point, but your machine's manual has the precise threading diagram for your exact model. Browse our catalogue to find it.